Toshiba E-Studio 5540c Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 118

background image

3 TROUBLESHOOTING FOR PRINTING

74 Hardware Problems

Hardware Problems

This section describes troubles caused by the hardware device (the equipment).

If an icon or a message indicating an error is not displayed, or the problems in the printer drivers or the network connection
cannot be specified, a hardware problem is a possible cause of the trouble.

The following are common factors involved in the hardware problems:

y

System board, cables, and connectors

y

The equipment, and its (optional) components such as the duplexing unit or the Finisher

y

System software or firmware of the equipment

Print jobs not output

Problem Description

All the clients within a network fail to make the equipment output the print jobs.

Corrective Action

There remains a possibility that improper settings of the software such as printer drivers caused the problem. However, a
hardware error is possible, if none of the clients can print the jobs. Try the steps on the checklist below. If the problem
persists after you have followed all of the steps, contact your service representative.

Also refer to the

Printing Guide

for more information on resolving output errors caused by software settings.

No

Check...

Yes

No

Corrective Action

1

Is printing prohibited from all connected client
computers?

Next Step

Ø

Ö

See the following section to fix the problem:

P.72 “Network Connection Problems”

2

Can you see the job from TopAccess or another
print monitoring utility, such as PCONSOLE or
Print Manager?

Next Step

Ø

Ö

See the following section to fix the problem:

P.82 “Locating the Equipment in the Network”

3

Can you identify the problem with the error
message or the error code and resolve it?

End

Ö

See the following sections to fix the problem:

P.96 “Error Messages”

P.98 “Error Codes”

«
...
74
75
76
77
78
...
»

Содержание E-Studio 5540c























































































































Отзывы:

Нет отзывов

Похожие инструкции для E-Studio 5540c

Бренд: TallyGenicom Страницы: 92

Бренд: Oki Страницы: 62

Бренд: TallyGenicom Страницы: 144

Бренд: Xerox Страницы: 205

VersaLink C400V

Бренд: Xerox Страницы: 196

Бренд: Oce Страницы: 230

Бренд: Linux Страницы: 8

Бренд: M&R Страницы: 36

Бренд: Lanier Страницы: 140

All in One Printer

Бренд: Epson Страницы: 210

aculaser cx37 series

Бренд: Epson Страницы: 261

AL-MX200 Series

Бренд: Epson Страницы: 410

AcuLaser CX29DNF

Бренд: Epson Страницы: 456

AL-MX300 Series

Бренд: Epson Страницы: 2

WorkForce Pro WF-C8190DTWC

Бренд: Epson Страницы: 162

WorkForce Pro WP-4095 DN

Бренд: Epson Страницы: 2

WorkForce Pro WP-4532

Бренд: Epson Страницы: 4

WorkForce Pro WP-4530

Бренд: Epson Страницы: 287

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды