manualshive.com logo in svg

Toshiba E-Studio 5540c, Руководство по устранению неисправностей

Принтер Toshiba E-Studio 5540c - мощное устройство для офиса. Для решения любых проблем с устройством, скачайте бесплатно Руководство по устранению неполадок на manualshive.com. На сайте вы найдете все необходимые инструкции для эффективной работы данного принтера. Безупречное качество печати и удобство использования вас приятно удивят.

Поделиться
Скачать
background image

7 CHECKING THE EQUIPMENT STATUS WITH TopAccess

104    Error Codes

2C6C

Invalid address specified in To: field

Make sure that there is no unpermitted character in the 
Destination mail address. Delete any unpermitted 
character and reset the appropriate Destination mail 
address, then try again.

2C70

SMTP service is not available

Ask your administrator whether the SMTP service is 
enabled.

2C71

SMTP authentication error

Confirm that the login name and password are correct. 
If SSL is enabled, make sure that the SSL port number 
is correctly set.

2C72

POP Before SMTP error

Confirm that the POP Before SMTP settings and POP3 
settings are correct.

2CC0

Job canceled

The job was canceled.

2CC1

Power failure occurred

Make sure that the power cable is connected properly 
and is inserted securely. Resend the job.

Save as File

2D10, 2D12, 

2D13

Wrong Job status

Turn the power OFF and then back ON. Try it again. If 
the error still persists, contact your service 
representative.

2D11

Not enough memory

Wait for a while and try again. If the error still persists, 
turn the power OFF and then back ON, and make 
another effort.

2D14

Invalid parameter specified

If you are using a template, create it again. If the error 
still persists, turn the power OFF and then back ON, 
and then try again.

2D15

Exceeding maximum file capacity

Divide the file into several files, or try again in a single-
page format.

2D30

Failure to create directory

Make sure that the access privilege to the storage 
directory is writable and also that the disk in the 
directory has enough space, and then try again. If more 
than one job is performed simultaneously, the error may 
occur because the disk temporarily runs out of space. In 
this case, wait for a while and try again. If the error still 
persists, turn the power OFF and then back ON, and 
make another effort.

2D31, 2D33

Failure to create file

Make sure that the access privilege to the storage 
directory is writable and also that the disk in the 
directory has enough space, and then try again. If more 
than one job is performed simultaneously, the error may 
occur because the disk temporarily runs out of space. In 
this case, wait for a while and try again. If the error still 
persists, turn the power OFF and then back ON, and 
make another effort.

2D32

Failure to delete file

Make sure that the access privilege to the storage 
directory is writable and then try the job again. If the 
error still persists, turn the power OFF and then back 
ON, and then make another effort.

2D40

Failure to convert image file format

This error occurs when conversion to a highly 
compressed PDF format fails. Do the scanning again. If 
the error still persists, Use the normal PDF 
format.When this error occurs in conversion other than 
to a highly compressed PDF format, turn the power 
OFF and then back ON. Then try to scan again. If the 
error still persists, contact your service representative.

2D43

Encryption error. Failure to create a file

If the error still persists after reattempting, turn the 
power OFF and then back ON. Then make another 
effort.

2D44

Creating a file was not allowed.

Creating an unencrypted file was not allowed. 
Configure the encryption settings and try again.To 
create an unencrypted file, consult the administrator.

2D45

Failure in making meta data

Make sure that the template setting is correct, and do 
the scanning again. If the error still persists, turn the 
power OFF and then back ON, and then try again.

Error Code

Problem Description

Corrective Action

Содержание E-Studio 5540c























































































































Отзывы:

Нет отзывов

Похожие инструкции для E-Studio 5540c

QMS 2001 Setup Manual preview
2001
Бренд: QMS Страницы: 26
Sagem MF9500 Facsimile Operation Manual preview
MF9500
Бренд: Sagem Страницы: 83
Canon imageRUNNER ADVANCE C3330 Series Replacement Procedure preview
imageRUNNER ADVANCE C3330 Series
Бренд: Canon Страницы: 5
Canon imagePROGRAF TA-30 Setup Manual preview
imagePROGRAF TA-30
Бренд: Canon Страницы: 49
Canon LX-P1300 User Manual preview
LX-P1300
Бренд: Canon Страницы: 210
Canon Color imageCLASS MF8180c Starter Manual preview
Color imageCLASS MF8180c
Бренд: Canon Страницы: 34
Olympus PS100 - Photo Printer - 50 Sheets Quick Start Manual preview
PS100 - Photo Printer - 50 Sheets
Бренд: Olympus Страницы: 2
Olivetti d-COLOR MF3300 Utility Keys preview
d-COLOR MF3300
Бренд: Olivetti Страницы: 69
Oki OKIPAGE 24DX Service Manual preview
OKIPAGE 24DX
Бренд: Oki Страницы: 424
Oce LightJet 430 Site Preparation Manual preview
LightJet 430
Бренд: Oce Страницы: 32
U-Line DYMO LABELWRITER 450 TURBO H-1265 Manual preview
DYMO LABELWRITER 450 TURBO H-1265
Бренд: U-Line Страницы: 9
NEC 4650NX - SuperScript Color Laser Printer Network Manual preview
4650NX - SuperScript Color Laser Printer
Бренд: NEC Страницы: 74
Lexmark CX310 series Specifications preview
CX310 series
Бренд: Lexmark Страницы: 2
Epson 5700i - EPL B/W Laser Printer Setup Manual preview
5700i - EPL B/W Laser Printer
Бренд: Epson Страницы: 33
Epson 2180 - LQ B/W Dot-matrix Printer Specifications preview
2180 - LQ B/W Dot-matrix Printer
Бренд: Epson Страницы: 2
Epson 2190 - FX B/W Dot-matrix Printer Specifications preview
2190 - FX B/W Dot-matrix Printer
Бренд: Epson Страницы: 2
Epson 2200 - Stylus Photo Color Inkjet Printer User Manual preview
2200 - Stylus Photo Color Inkjet Printer
Бренд: Epson Страницы: 62
Epson 24-PIN DOT MATRIX PRINTER LQ-680PRO Specifications preview
24-PIN DOT MATRIX PRINTER LQ-680PRO
Бренд: Epson Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды