Toshiba E-Studio 5540c Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 118

background image

1 TROUBLESHOOTING FOR THE HARDWARE

16 Clearing a Paper Jam

If paper jams occur frequently

The following are the common causes of paper jams. If the problem persists, check for the following situations.

y

An unsuitable original is placed on the Reversing Automatic Document Feeder.

y

Paper unsuitable for the equipment is used.

y

Paper sizes are not consistent between the size in a drawer or the bypass tray and the size registered in the
equipment.

y

All the jammed paper has not been removed.

y

There is too much of a gap between the paper and the side or end guide in the drawer.

y

The amount of paper placed in a drawer exceeds the limit indicated on its side guide.

Paper jam in the Reversing Automatic Document Feeder (lower)

Do not touch the fuser unit or the metal portion around it.

Do not touch the fuser or the metal portion around it when you remove the
jammed paper from the fuser unit. This could burn you or the shock could
cause you to injure your hand in the machine.

Do not touch the transfer belt.

Do not touch the transfer belt when you remove the jammed paper inside
the right side of the equipment. Doing so may damage to the equipment or
result in a poor output.

1

Open the Reversing Automatic Document Feeder.

2

Push the green lever, open the reverse cover and
remove the original.

«
...
16
17
18
19
20
...
»

Содержание E-Studio 5540c























































































































Отзывы:

Нет отзывов

Похожие инструкции для E-Studio 5540c

Бренд: Canon Страницы: 149

Бренд: Canon Страницы: 60

Бренд: Lanier Страницы: 4

Бренд: Fastjet Страницы: 52

DocuPrint C3055 DX

Бренд: Xerox Страницы: 20

Бренд: Oki Страницы: 62

Бренд: TallyGenicom Страницы: 144

Бренд: Panasonic Страницы: 240

Бренд: Ricoh Страницы: 126

Бренд: Star Страницы: 24

Бренд: Ricoh Страницы: 159

Бренд: Muratec Страницы: 6

Бренд: iDPRT Страницы: 74

Бренд: Memjet Страницы: 181

WorkCentre WC7545

Бренд: Xerox Страницы: 8

Бренд: AstroJet Страницы: 32

Бренд: Roland Страницы: 116

SmartBase 1270D

Бренд: Canon Страницы: 406

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды