Toshiba E-Studio 5540c Скачать руководство пользователя страница 73

Страница: 73 / 118

3.TROUBLESHOOTING FOR PRINTING

Printer Driver Problems 71

3 TROUBLESHOOTING FOR PRINTING

Retrieval of printer configuration failed

Problem Description

When accessing the printer properties, the message “Retrieval of printer configuration failed” is displayed.

Corrective Action

The printer driver cannot communicate with the equipment. Try the steps in the checklist below.

Cannot change settings on the [Device Settings] tab

Problem Description

The [Device Settings] tab is grayed out and their settings cannot be changed.

Corrective Action

Users who do not have the privilege to change the printer driver setting cannot change the options in the [Device Settings]
tab. Please log on with the Administrator.

Check...

Yes

Corrective Action

Is the equipment turned on?

Next Step

Turn on the equipment.

Can you connect the computer to the equipment
via TopAccess?

Next Step

Restart the equipment.

Does the same message appear again when you
access the property of the printer driver?

End

Check the printer driver port assignment and
make sure that it is correct.

Содержание E-Studio 5540c























































































































Результаты поиска

Содержание E-Studio 5540c

Отзывы:

Похожие инструкции для E-Studio 5540c

Бренды по названию

Популярные бренды

Toshiba E-Studio 5540c, Руководство по устранению неисправностей

Результаты поиска

Содержание E-Studio 5540c

Отзывы:

Похожие инструкции для E-Studio 5540c

Бренды по названию

Популярные бренды