Toshiba E-Studio 5540c Скачать руководство пользователя страница 31

Страница: 31 / 118

1.TROUBLESHOOTING FOR THE HARDWARE

Clearing a Paper Jam 29

1 TROUBLESHOOTING FOR THE HARDWARE

Paper jam in the Saddle Stitch unit (optional)

The Saddle Stitch unit is inside the Saddle Stitch Finisher MJ-1104.

Separate the finisher from the equipment.

1) Open the front cover of the finisher when the Hole Punch Unit is not installed. Open the Hole Punch Unit cover

when the Hole Punch Unit is installed.

2) Pull the lever to unlock the finisher.

3) Placing your hands on the positions shown in the figure, move the finisher slowly until it stops, and then open

the front cover of the finisher.

Remove the jammed paper from the exit side of the
Saddle Stitch unit.

Remove the jammed paper from the entrance of the
finisher.

When the Hole Punch Unit is not installed

When the Hole Punch Unit is installed

When the Hole Punch Unit is not installed

When the Hole Punch Unit is installed

Содержание E-Studio 5540c























































































































Результаты поиска

Содержание E-Studio 5540c

Отзывы:

Похожие инструкции для E-Studio 5540c

Бренды по названию

Популярные бренды

Toshiba E-Studio 5540c, Руководство по устранению неисправностей

Результаты поиска

Содержание E-Studio 5540c

Отзывы:

Похожие инструкции для E-Studio 5540c

Бренды по названию

Популярные бренды