Toshiba E-Studio 5540c Скачать руководство пользователя страница 25

Страница: 25 / 118

1.TROUBLESHOOTING FOR THE HARDWARE

Clearing a Paper Jam 23

1 TROUBLESHOOTING FOR THE HARDWARE

Fuser unit

Close the duplexing unit putting your hands on the
position shown in the figure.

Do not put your hand or fingers on the duplexing unit when
closing it.

They could be caught and this could injure you.

Pushing the lock lever, pull out the duplexing unit
from the equipment until it stops.

Be careful not to touch the slide rails (A in the figure).

This could injure you.

Holding the green lever, pull out the transport guide
toward you.

Check the inside of the fuser unit for the hidden
jammed paper when you cannot see it.

1) Open the front cover of the equipment.

2) Check if jammed paper remains inside the fuser unit through the

window for checking for paper jams.

3) Close the front cover of the equipment.

Содержание E-Studio 5540c























































































































Результаты поиска

Содержание E-Studio 5540c

Отзывы:

Похожие инструкции для E-Studio 5540c

Бренды по названию

Популярные бренды

Toshiba E-Studio 5540c, Руководство по устранению неисправностей

Результаты поиска

Содержание E-Studio 5540c

Отзывы:

Похожие инструкции для E-Studio 5540c

Бренды по названию

Популярные бренды