manualshive.com logo in svg

Toshiba E-Studio 5540c, Руководство по устранению неисправностей

Принтер Toshiba E-Studio 5540c - мощное устройство для офиса. Для решения любых проблем с устройством, скачайте бесплатно Руководство по устранению неполадок на manualshive.com. На сайте вы найдете все необходимые инструкции для эффективной работы данного принтера. Безупречное качество печати и удобство использования вас приятно удивят.

Поделиться
Скачать
background image

7.CHECKING THE EQUIPMENT STATUS WITH TopAccess

Error Codes    103

7 CHECKING THE EQUIPMENT STATUS WITH TopAccess

„

Error codes on scan jobs

The error indications on scan jobs are done as follows:

y

On TopAccess log list, messages indicating the status are displayed.

y

On the touch panel of the equipment, error codes are displayed. See the listings below.

Error Code

Problem Description

Corrective Action

Email

2C10, 2C12, 

2C13, 

2C20-2C22

Wrong Job status

A system error has occurred during the sending of an 
Email. Try it again. If the error still persists, contact your 
service representative.

2C11

Not enough memory

Complete any running jobs first before reperforming the 
job in error. If the error still persists, turn the power OFF 
and then back ON, and then try again.

2C14

Invalid parameter specified

If you are using a template, create it again. If the error 
still persists, turn the power OFF and then back ON, 
and then try again.

2C15

Mail size exceeded limit or maximum size

You are sending too many documents at a time. Send 
them separately.

2C30-2C33

Disk access error

Complete any running jobs first before reperforming the 
job in error. If the error still persists, turn the power OFF 
and then back ON, and then try again.

2C40

Failed to convert image file format

This error occurs when conversion to a highly 
compressed PDF format fails. Do the scanning again. If 
the error still persists, Use the normal PDF 
format.When this error occurs in conversion other than 
to a highly compressed PDF format, turn the power 
OFF and then back ON. Then try to scan again. If the 
error still persists, contact your service representative.

2C43

Encryption error. Failure to create a file

If the error still persists after reattempting, turn the 
power OFF and then back ON. Then make another 
effort.

2C44

Creating a file was not allowed

Creating an unencrypted file was not allowed. 
Configure the encryption settings and try again.To 
create an unencrypted file, consult the administrator.

2C45

Failure in making meta data

Make sure that the template setting is correct, and do 
the scanning again. If the error still persists, turn the 
power OFF and then back ON, and then try again.

2C60

HDD full failure during processing

Reduce the number of pages of the problem job and try 
again. Check whether the server or local disk has 
sufficient space in its capacity.

2C61

Failure to read Address Book

Turn the power OFF and then back ON. Try the 
problem job again. Reset the data in the Address Book 
and reattempt it. If the error still persists, contact your 
service representative.

2C63

Terminal IP address unset

Ask your administrator to set the IP address of the 
equipment.

2C64

Terminal mail address unset

Ask your administrator to set the Email address of the 
equipment.

2C65, 2C66, 

2C69

Failure to connect to SMTP server

Make sure that the SMTP server is correctly working or 
the SMTP server address has been set correctly.

2C6A

Failure to send Email message

Turn the power OFF and then back ON. Try scanning 
again. If the error still persists, contact your service 
representative.

2C6B

Invalid address specified in From: field

Ask your administrator to check the SMTP 
Authentication method or if there is an unpermitted 
character in the Terminal mail address. Set the correct 
SMTP Authentication method or delete the unpermitted 
character in the Terminal mail address.

Содержание E-Studio 5540c























































































































Отзывы:

Нет отзывов

Похожие инструкции для E-Studio 5540c

Panasonic Workio DP-C265 Operating Instructions Manual preview
Workio DP-C265
Бренд: Panasonic Страницы: 102
BadgePass NXT5000 Quick Start Manual preview
NXT5000
Бренд: BadgePass Страницы: 2
Raymarine e7 Installation And Operation Handbook preview
e7
Бренд: Raymarine Страницы: 135
Xerox PHASER 6121MFP Service Manual preview
PHASER 6121MFP
Бренд: Xerox Страницы: 532
Xerox Phaser 6120 User Manual preview
Phaser 6120
Бренд: Xerox Страницы: 174
Xerox Phaser 6115 MFP Repacking Manual preview
Phaser 6115 MFP
Бренд: Xerox Страницы: 2
Xerox Phaser 6115 MFP User Manual preview
Phaser 6115 MFP
Бренд: Xerox Страницы: 219
Xerox PHASER 6010 Quick Use Manual preview
PHASER 6010
Бренд: Xerox Страницы: 5
Xerox Phaser 6140N Product Safety Data Sheet preview
Phaser 6140N
Бренд: Xerox Страницы: 3
Xerox Phaser 6128 MFP Installation Manual preview
Phaser 6128 MFP
Бренд: Xerox Страницы: 2
Xerox Phaser 6128 MFP Evaluator Manual preview
Phaser 6128 MFP
Бренд: Xerox Страницы: 16
Xerox Phaser 6125 Specifications preview
Phaser 6125
Бренд: Xerox Страницы: 2
Xerox Phaser 7800 Training preview
Phaser 7800
Бренд: Xerox Страницы: 9
Xerox Phaser 7800 Quick Manual preview
Phaser 7800
Бренд: Xerox Страницы: 12
Xerox Phaser 7750 Adding Memory Manual preview
Phaser 7750
Бренд: Xerox Страницы: 2
Xerox Phaser 7750 Setup Manual preview
Phaser 7750
Бренд: Xerox Страницы: 2
Xerox Phaser 8500 Quick Manual preview
Phaser 8500
Бренд: Xerox Страницы: 4
Xerox Phaser 8500 Detailed Specifications preview
Phaser 8500
Бренд: Xerox Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды