Toshiba Carrier MMC-AP0181H2UL Скачать руководство пользователя страница 106

Страница: 106 / 178

106

No.

Part name

Adjust corner

cap

Procedure

1. Detachment

1) Pull knob of the adjust corner cap to the

arrow direction, remove strap of the

adjust corner cap from pin of the panel

and then remove all the 4 corners of the

cap.

NOTE :

The knob is provided to only one side.
Be sure to remove the cap of the knob side

at first.

2. Attachment

1) Hook the strap of the adjust corner cap

securely to the pin of the ceiling panel.

2) Insert the 2 claws “A” of the adjust corner

cap into rectangular holes of the ceiling

panel in the direction of the arrow.

3) Press the adjust corner cap so that the

3 claws “B” on the back of the cap are

fitted.

Remarks

Pulling direction

Knob

Adjust corner cap

Claws “A” (Insert to fit)

Claws “B” (Push to fit)

Rectangular
holes

Claws “A”

Claws “B”

Firmly push edges
of the adjust corner cap.

Содержание Carrier MMC-AP0181H2UL



















































































































































































Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды

Toshiba Carrier MMC-AP0181H2UL, Руководство по обслуживанию

Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды