Toshiba Carrier MMC-AP0181H2UL Скачать руководство пользователя страница 71

Страница: 71 / 178

SET

TIME

TIMER SET

TEST

FILTER

RESET

TEMP.

FAN

SAVE

SWING/FIX

VENT

MODE

ON / OFF

UNIT LOUVER

1 2 3 4 5
6 7 8

END

SET

TIME

TIMER SET

TEST

FILTER

RESET

TEMP.

FAN

SAVE

SWING/FIX

VENT

MODE

ON / OFF

UNIT LOUVER

Cancel of line selection

When you want to
complete the setting

Finish

How to change all indoor addresses from an arbitrary wired remote controller

(It is possible when setting has finished by automatic addresses.)

Contents:

The indoor unit addresses in each identical refrigerant piping line can be changed from an

arbitrary wired remote controller.

Enter in address check/change mode and then change the address.

<Procedure>

Carry out this procedure during stop of system.

Push the timer time button

TEST

simultaneously for 4 seconds or more.

First line 1 and CODE No.

(Address Change) are displayed.

Select line address using

UNIT LOUVER

SWING/FIX

button.

Push the

SET

button.

• The address of the indoor unit connected to the

refrigerant piping of the selected outdoor unit is

displayed and the fan and the louver are on.
First the current indoor address is displayed.

(Line address is not displayed.)

TIME

button push up/down the indoor

address of the SET DATA.

The set data is changed to a new address.

Push

SET

button to determine the set data.

Every pushing

UNIT LOUVER

button, the indoor unit

No. in the identical piping is displayed one

after the other.

• Only fan and louver of the selected indoor unit

start operation.
Repeat the Procedures

to change all the

indoor addresses so that they are not duplicated.

Push

SET

button.

(All the indications of LCD go on.)

Push

TEST

button and then the procedure

finishes.

If the UNIT No. is not call up here, the outdoor unit

in that line does not exist.
Push

button to select a line again in the

Procedure

Содержание Carrier MMC-AP0181H2UL



















































































































































































Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды

Toshiba Carrier MMC-AP0181H2UL, Руководство по обслуживанию

Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды