Toshiba Carrier MMC-AP0181H2UL Скачать руководство пользователя страница 35

Страница: 35 / 178

No.

Item

Display of

[READY]

[HEAT READY]

Selection of

central control

mode

Outline of specifications

< READY>

Displayed on the remote controller

1) When the following check codes are indicated

• Open phase of power supply wiring [P05] was detected.
• There is an indoor unit that detected the indoor overflow

[P10].

• There is an indoor unit that detected the interlock alarm

[L30].

2) During Force Thermo-OFF

• [COOL/DRY] operation is unavailable because the other

indoor unit operates with [HEAT] mode.

• [HEAT] operation is unavailable because COOL priority

(SW11-bit1 of the Outdoor I/F P. C. board is ON) is set and

the other indoor unit operates with [COOL/DRY] mode.

3) The above indoor units that cannot operate stay in

Thermo-OFF status.

4) The indoor fan stops because the system performs

[Recovery operation for heating refrigerant (Oil)].

<HEAT READY>

Displayed on the remote controller

1. Normal thermo. OFF

• During heating, the indoor unit goes thermo OFF as the

heating temperature setting is reached.

2. During heating, the fan rotates at a breeze speed

(UL or lower) or remains stationary to prevent cold air

from being discharged (including defrosting operation).

3. Forced thermo OFF

• “HEAT” operation is unavailable because at least one

indoor unit is operating in “COOL/DRY” mode under

priority cooling setting (bit 1 of SW11 on outdoor I/FP.C.

board ON).

1) Selection of the contents that can be operated by the remote controller at the indoor

unit side is possible according to setting at the central controller side.

2) Setting contents

• In case of TCC-LINK central control

(

{

: Operation possible

: Operation impossible)

Remarks

•

<READY

display

No display for wireless

type remote controller

•

<HEAT READY

display

Operation from

TCC-LINK

central control

Individual

[Central 1]
[Central 2]
[Central 3]
[Central 4]

Operation on RBC-AMT32E

ON/OFF

Operation

Timer

Temp.

Air speed

Air direction

setting

selection

setting

{

RBC-AMT32E

[Central control]

display

Содержание Carrier MMC-AP0181H2UL



















































































































































































Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды

Toshiba Carrier MMC-AP0181H2UL, Руководство по обслуживанию

Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды