Toshiba Carrier MMC-AP0181H2UL Скачать руководство пользователя страница 120

Страница: 120 / 178

120

No.

Part name

Fan guard

Bell mouth

Turbo fan

Procedure

1. Detachment

1) Perform work of procedure

-1.

2) Take off screws and clamp fixing the fan guard.

(Ø4 × 0.39"(10mm), [Screws for plastic

molding] 3 pcs.))

NOTE)

The specification of fixing screws for the fan guard

differs from those of other fixing screws.

Therefore keep them separately from other screws.

2. Attachment

1) Attach screws and clamp for fixing the fan guard.

(Ø4 × 0.39"(10mm), [Screws for plastic

molding] 4 pcs.))

1. Detachment

1) Perform work of procedure

-1.

2) Take off the lead wires of the drain pump, float

switch, and fan motor from the bell mouth.

3) Take off fixing screws of the bell mouth.

(Ø4 × 0.31"(8mm), 4 pcs.))

2. Attachment

1) Mount the bell mouth with screws.

(Ø4 × 0.31"(8mm), 4 pcs.))

2) Perform wiring as original before being

removed.

NOTE)

Pinch lead wire of the drain pump and float switch

with lead wire fixing claws of the bell mouth and

perform wiring along the guide.

1. Detachment

1) Perform work of procedure

-1.

2) Take off the nut (M6 nut 1 pc.) of the turbo fan.

NOTE)

Use a box wrench for attachment and detachment of

the turbo fan. If using a monkey wrench etc, the other

parts may be damaged in work.

2. Attachment

1) Insert the turbo fan into the fan motor so that

boss of the turbo fan matches with cut surface

of the fan motor, and then tighten it with nut.

NOTE)

Tightening torque of turbo fan: 4.4 ± ft.lbs(5.9 ±

0.6Nm)
Apply looseness-preventing agent to the nut after

tightening.

Remarks

Fan guard

Clamp

4 screws

Fixing claws
for lead wires

Bell mouth

4 screws

Fixing claws
for lead wires

Drawing-out port of
fan motor lead wire

Fan motor fixing
M6 nut

Turbo fan

Содержание Carrier MMC-AP0181H2UL



















































































































































































Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды

Toshiba Carrier MMC-AP0181H2UL, Руководство по обслуживанию

Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды