Toshiba Carrier MMC-AP0181H2UL Скачать руководство пользователя страница 117

Страница: 117 / 178

117

No.

Part name

Adjust

corner cover

Ceiling

panel

Procedure

1. Detachment

1) Perform work of procedure of

-1.

2) Turn clockwise screws (4 positions) at the

suction port corner until adjust corner

cover rises up.

NOTE)

When you work, keep the torque at below

8.9ft.lbs12Nm.
Do not use an electric screwdriver; otherwise the

mechanism of adjust corner cover may be

damaged and not be removed.

3) Pull downward the risen-up part of adjust

corner cover and remove it.

4) Remove the strap of adjust corner cover.

2. Attachment

1) Attach the strap of adjust corner cover to

the panel, hook claws of adjust corner

cover to the panel corner, and then push

the opposite side into the panel.

2) Turn screws (4 positions) of the suction

port corner counterclockwise until bump

between adjust corner cover and panel

disappears.

NOTE)

When you work, keep the torque at below 8.9ft.lbs12Nm.
Do not use an electric screwdriver;

otherwise the mechanism of adjust corner cover

may be damaged and not be removed.

1. Detachment

1) Perform works of procedure

-1, and

-1.

2) Remove the flap connector (CN33, White,

5P) connected to the control P.C. board

and then take off the lead wire from the

clamp.

NOTE)

Remove the connectors after unlocking the lock

of the housing.

3) Take off screws (M5, 4 pcs.) fixing the

ceiling panel.

4) Push the temporary bracket to inner side to

remove the ceiling panel.

2. Attachment

1) Hook the panel to the temporary bracket of

the drain pan of the main body.

NOTE)

The panel has directionality. Therefore mount the

panel according to the temporary bracket and the

bracket mounting position.

2) Tighten the fixing screws. (M5, 4 pcs.)
3) Connect flap connector of the ceiling

panel to the connector

(CN33, White, 5P) of the control

P.C. board.

Remarks

Hanging
section of tentative
hook of ceiling panel

Temporary
bracket

Push to remove

Drain piping
corner

Ceiling panel

Hanging section
of temporary bracket

Washer
based screw

Temporary
bracket

Cable clamp

CN33

Torque~8.9ft.lbs(12N·m)

Torque~ 8.9ft.lbs
(12Nm)

Содержание Carrier MMC-AP0181H2UL



















































































































































































Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды

Toshiba Carrier MMC-AP0181H2UL, Руководство по обслуживанию

Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды