Toshiba Carrier MMC-AP0181H2UL Скачать руководство пользователя страница 111

Страница: 111 / 178

111

Remarks

2) Fix the fan motor lead, TC sensor and TCJ

sensor with the clamp of the bell mouth.

3) Mount the electric parts box with the fixing

screws “A and B”.

(M4, 0.39"( 10 mm ), 3 pcs. M4, 0.31"( 8 mm ),1 pc.)

4) Connect the connector, the power supply

wire and the remote controller wire as

before, which were removed in

Detachment work 2) and 3) in previous

page, and then fix wiring with clamp.

5) Following to work of Attachment of

mount the electric parts box cover and the

suction grille as before.

No.

Part name

Fan motor

(Continued)

Procedure

7) Remove the fixing screws and then remove

the bell mouth. (M4, 0.39"(10 mm), 8 pcs.)

8) Remove the fixing screws and then remove

the nut cap. (M4, 0.39"(10 mm), 2 pcs.)

9) Remove the fixing nut and then remove the

turbo fan. (M8 nut with flange, 1 pc.)

10) Remove the fixing screws and then

remove the motor lead holding bracket.

(M4, 0.31"(8 mm), 2 pcs.)

11) Cut the bundling band and then remove it

from the clamp.

12) Remove the fixing nut and then remove

the fan motor. (M6 nut, 3 pcs.)

2. Attachment

1) Fix the parts as before in order of fan

motor

→

motor lead holding bracket

→

turbo fan

→

nut cap

→

bell mouth, fan

guard.

NOTE :

Fix the motor lead to the clamp without

slack as before using bundling band.

When fixing the turbo fan, be sure to match

the D-cut of the fan boss with D-cut of the

motor shaft. Using a torque wrench, fix the

turbo fan and tighten in to 4.0 ft.lbs(5.4
Nm).

Using torque wrench, fix the fan motor (at 3
positions) and tighten it to 3.6

ft.lbs(4.9

Nm).

Clamp

Fan motor lead

M6 nut

Fan motor

Motor lead
holding bracket

Fan motor

Motor lead
holding bracket

Fixing screws (Ø4 × 8)

Bell mouth

Nut cap

Fixing scre

Fixing screw

Bell mouth

Nut cap

Fixing screw

M8 nut with flange

Turbo fan

M8 nut with flange

Turbo fan

+0.5

–0.2

+0.4

–0.1

+0.4

–0.2

+0.5

–0.2

Содержание Carrier MMC-AP0181H2UL



















































































































































































Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды

Toshiba Carrier MMC-AP0181H2UL, Руководство по обслуживанию

Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды