Toshiba Carrier MMC-AP0181H2UL Скачать руководство пользователя страница 130

Страница: 130 / 178

130

No.

Part name

Fan, Shaft,

Bearing,

Coupling,

Fan case

(Continued)

Procedure

2. Attachment

1) Mount a fan to the shaft. Refereeing to the

right photo, arrange the tightening screw at the

right side of the fan against the make-up panel.
On boss of the fan, there is attached a groove

to escape a scratch received when mounting

the hexagon socket head screw to the shaft.
Mount it while aligning scratch of the shaft and

groove of the fan.
Tightening is carried out in the following work.

2) If mounting of bearing to the shaft is required,

mount it in the work of 1).

(For only AP036 to AP042 only)
A groove is provided on the shaft in order to

match the mounting position with the bearing.

Mount the bearing by aligning the single face

of bearing to the groove and then fix it with

hexagon socket head screws (2 positions).

NOTE :

Use a torque wrench for fixing with 1.8 to 2.5 ft.lbs(2.5

to 3.4Nm).

3) Put the shaft which was inserted with the fan

into the coupling.
Tightening is carried out in the following work.

4) Mount the bearing in the main unit as before.

NOTE :

Put into the bearing spacer between base and

cover and then fix the bearing spacer with bolts

(M8, 0.47"(12 mm), 2 pcs.))

5) Fix the coupling with the hexagon socket head

screws.
A groove is provided on the shaft in order to

match the mounting position with the coupling.
Mount the coupling by aligning the single face

of coupling to the groove and then fix it.

NOTE :

Use a torque wrench for fixing with 3.6 ft.lbs (4.9Nm)

or more.

6) Position the fan so that the fan locates at the

center against the fan case (top) and then fix it

with the hexagon socket head screws.

NOTE :

Use a torque wrench for fixing with 3.6 ft.lbs (4.9Nm)

or more.

7) Mount the fan case (top) as before.

Finally, check the fan turns surely and smoothly.

8) Carry out works 2) and 3) of Attachment of

Remarks

Arrange so that screws are at right side

Arrange so that screws are at right side
against the bottom make-up panel.

against the bottom make-up panel.

Arrange so that screws are at right side
against the bottom make-up panel.

Bottom
make-up panel

Coupling

Shaft groove

Coupling

Escape groove of screw

Shaft

Escape groove of screw

Shaft

Bearing

Match the shaft groove and

Fan case (top)

Bearing

Arrange so that the fan locates

Arrange so that the fan locates
at the center of the fan case.

at the center of the fan case.

Shaft groove

Fan case (top)

Bearing

Arrange so that the fan locates
at the center of the fan case.

Содержание Carrier MMC-AP0181H2UL



















































































































































































Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды

Toshiba Carrier MMC-AP0181H2UL, Руководство по обслуживанию

Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды