Toshiba Carrier MMC-AP0181H2UL Скачать руководство пользователя страница 59

Страница: 59 / 178

<In case of wireless remote controller>

Procedure

Description

Turn on power of the air conditioner.

The operation is not accepted for 5 minutes when power has been turned on at first time after installation,

and 1 minute when power has been turned on at the next time and after.
After the specified time has passed, perform a test operation.

Push [

Start/Stop

] button and change the operation mode to [

COOL

] or [

HEAT

] with [

Mode

] button.

Then change the fan speed to [

High

] using [

Fan

] button.

Test cooling operation

Test heating operation

Set temperature to [64°F (18°C)] using

Set temperature to [86°F (30°C)] using

[

Temperature set

] button.

[

Temperature set

] button.

After checking the receiving sound “Pi”,

immediately push [

Temperature set

] button to

immediately push [

Temperature set

] button to

set to [66°F (19°C)]

set to [84°F (29°C)].

After checking the receiving sound “Pi”,

immediately push [

Temperature set

] button to

immediately push [

Temperature set

] button to

set to [64°F (18°C)].

set to [86°F (30°C)].

Then repeat the procedure

→

After approx. 10 seconds, all the display lamps on the sensor part of wireless remote controller,

[

Operation

] (Green), [

Timer

] (Green), and [

Ready

] (Yellow) flash and the air conditioner starts operation.

If the lamps do not flash, repeat the procedure

and after.

After the test operation, push [

Start/Stop

] button to stop the operation.

3, 4, 5, 6

2, 7

Be sure to set the
air speed to [High]

Содержание Carrier MMC-AP0181H2UL



















































































































































































Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды

Toshiba Carrier MMC-AP0181H2UL, Руководство по обслуживанию

Результаты поиска

Содержание Carrier MMC-AP0181H2UL

Отзывы:

Похожие инструкции для Carrier MMC-AP0181H2UL

Бренды по названию

Популярные бренды