Toro Greensmaster 1018 Скачать руководство пользователя

Страница: 73 / 179

Assembly of Drum Drive Assembly

g258942

Figure 30

Drum hub

Spacer

Ball bearing (2 each)

Spacer

Drum spindle

Lock nut

Seal (2 each)

Note:

The seal side of each bearing (item 7 in

Figure 30

) should face inside

of the drum hub; refer to

Figure 30

1. Use a press to install the bearings (7) and spacer (8) into the drum hub

(10). Pack the bearings with grease. Fill outside space of the bearing with
the grease.

2. Apply a coat of grease to the seals (6). Press the seals (6) into the drum hub

(1) with its flat side facing outside; refer to

Figure 30

3. Apply grease to the shaft of the drum spindle (5). Carefully slide the drum

spindle into the drum hub bearings (7). Secure the drum spindle and drum
hub (1) with a spacer (2) and lock nut (3). Make sure that the drum spindle
(5) can move axially relative to the drum hub (1).

Note:

The lock nut (3) turns hard on the drum spindle (5) when tightened.

Ensure that all rotation has stopped when tightening. A good solid sound
indicates the nut is full tight.

4. Install the drum hub plate (4) into the traction drum (1) and secure with

shoulder bolt (11).

Note:

The fit between the drum hub plate (item 4 in

Figure 29

) and drum (1)

is a close tolerance and can be easily jammed. The hub can be rotated when
seated properly in the bore of the drum.

5. Secure the drum hub plate (4) to the drum hub (10) with the 4 bolts (2) and

washers (3). Tighten the bolts using an alternating pattern. Repeat tightening
sequence a second time.

6. Secure the drum hub plate (4) to the drum spindle (5) with the 4 bolts (2)

and washers (3). Tighten the bolts using an alternating pattern. Repeat
tightening sequence a second time.

Greensmaster

1018/1021/1026

Page 5–19

Traction and Reel Drive Systems: Service and Repairs

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды