Toro Greensmaster 1018 Скачать руководство пользователя

Страница: 70 / 179

Assembly of Drum Drive Gear Box Assembly (continued)

12. Install the drum drive cover (14) to the drum drive housing (25) and secure

with 5 socket head screws (15). Torque tighten the socket head screws to

1.7 to 4.5 N∙m (15 to 40 in-lb)

. Use an alternation pattern and torque tighten

the socket head screws to

9.6 to 10.7 N∙m (85 to 95 in-lb)

13. Fill the drum drive gear box assembly with

10 oz (0.56 lb)

of Mobil SCH007

grease.

14. Torque tighten the hollow plugs (16) from

12.4 to 14.6 N·m (110 to 130 in-lb)

Installing the Drum Drive Gear Box Assembly

1. If removed, apply a coat of loctite (blue) to threads of the hexagonal shaft (7).

Install the hexagonal shaft (item 7 in

Figure 25

) to the drum drive gear box

assembly (8). Torque tighten the hexagonal shaft to

67.7 N·m (50 ft-lb)

2. Apply a light coat of grease and install the O-ring (29) to the drum drive

housing (25).

3. Install the drum drive gear box assembly (8) to the frame assembly (9) and

secure with the shoulder bolt (10).

4. Install the drum drive gear box assembly (8) to the traction drum (2) and

secure with the 3 shoulder bolts (6).

5. Install the 2 splined couplers onto the transmission gear box assembly (1)

and drum drive gear box assembly (8) and secure with the truss screw (11),
2 washers (4) and nut (5).

6. Torque tighten the truss screw (11) to

10 to 12.4 N∙m (90 to 110 in-lb)

7. If required, install the transport wheels; refer to

Installing the Transport Wheel

(page 7–29)

8. Attach the spark plug wire to the spark plug.

Traction and Reel Drive Systems: Service and Repairs

Page 5–16

Greensmaster

1018/1021/1026

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды