Toro Greensmaster 1018 Скачать руководство пользователя страница 7

Страница: 7 / 179

Service Procedure Icons

The following icons appear throughout this Service Manual to bring attention to
specific important details of a service procedure.

Critical Process

This icon is used to highlight:

•

installing safety equipment (shields, guards, seat belts, brakes and R.O.P.S.
components) that may have been removed.

•

dimensions or settings that must be maintained for proper machine operation.

•

a specific fastener tightening sequence.

•

component orientation that may not be obvious.

Critical Torque

This icon is used to highlight an assembly torque requirement that is different
than what is recommended in the Standard Torque Tables; refer to

Torque

Specifications (page 2–6)

Fluid Specifications

This icon is used to highlight fluid specifications and capacities that are less
common, and may not appear on the machine service decal or in the machine

Operator’s Manual

Note:

Refer to the service decal on the machine and the machine

Operator’s

Manual

for commonly used fluid specifications and capacities.

Greensmaster

1018/1021/1026

Page 7

Preface

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды