Toro Greensmaster 1018 Скачать руководство пользователя

Страница: 56 / 179

General Information

The

Operator’s Manual

provides information regarding the operation, general

maintenance, and maintenance intervals for your machine. Refer to the

Operator’s Manual

for additional information when servicing the machine.

Disengaging The Drum Drive From Transmission

g258467

Figure 19

Transmission gear box assembly

Traction engage/disengage lever

The traction drum is driven by series of spur gears inside the transmission gear
box assembly. To disengage the traction drum drive from the transmission, do
the following procedure:

1. Park the machine on a level surface. Ensure that the engine is OFF. Remove

the spark plug wire from the engine spark plug.

2. Locate the traction engage/disengage lever on top of the transmission gear

box assembly.

3. To disengage the drum drive, rotate the traction engage/disengage lever

to clockwise direction (away from the center of transmission gear box
assembly).

4. To engage the drum drive, rotate the traction engage/disengage lever to

anti-clockwise direction (towards the center of the transmission gear box
assembly).

5. Attach the spark plug wire to the spark plug.

Traction and Reel Drive Systems: General Information

Page 5–2

Greensmaster

1018/1021/1026

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды