Toro Greensmaster 1018 Скачать руководство пользователя

Страница: 114 / 179

Removing the Clutch Cable (continued)

B. Remove the retaining ring (4) that secures the clutch cable eyelet (3) to

the clutch lever (5) and slide and remove the clutch cable eyelet from
the clutch lever.

4. Remove the control cover and lower cover from the handle assembly to allow

access to upper end of the clutch cable (item 1 in

Figure 52

5. Remove the clutch cable (1) from the link assembly (7) as follows:

A. Loosen the lower cable jam nut (2) that secures the clutch cable to the

upper receiver weldment (9). Slide the clutch cable from the upper
receiver weldment.

B. Remove the cable spring (3) from the link assembly (7). Note the

orientation of cable spring hook on the shaft assembly for assembly
purposes.

6. Remove the clutch cable (1) from the machine.

Installing the Clutch Cable

1. Secure the clutch cable (item 1 in

Figure 52

) to the clutch lever assembly as

follows:

A. Install the cable spring (3) to the link assembly. Orientate the cable spring

hook end toward front of the machine.

B. Slide the cable housing into the upper receiver weldment (9). Ensure that

the jam nut (2), flat washer and lock washer are on both sides of the
bracket. Adjust jam nuts so that equal amount of cable threads are visible
above the jam nuts. Leave the jam nuts snug until final cable adjustment.

2. Route the clutch cable (item 1 in

Figure 53

) to the transmission and install

the cable as follows:

A. Slide the cable eyelet (3) to the clutch lever (5) and secure with a

retaining ring (4).

B. Position the clutch cable (1) to the casting slot of the engine base with a

jam nut (2), flat washer and a lock washer on each side of the slot.

3. Make final adjustment of the clutch cable at the clutch cable lever assembly.

Adjust the cable jam nuts to remove the slack in the clutch cable.

4. Check the clutch cable adjustment; refer to

Operator’s Manual

5. Install the lower cover and control cover to the handle assembly.

6. Attach the spark plug wire to the engine spark plug.

Controls, Wheels and Accessories : Service and Repairs

Page 7–10

Greensmaster

1018/1021/1026

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды