Toro Greensmaster 1018 Скачать руководство пользователя

Страница: 113 / 179

Replacing the Clutch Cable

g261995

Figure 52

Clutch cable

Split bushing

Link assembly

Jam nut

Main control shaft

Cotter pin

Cable spring

Clevis pin

Upper receiver weldment

Removing the Clutch Cable

Note:

Refer to

Figure 52

during this procedure.

1. Park the machine on a level surface. Ensure that the engine is OFF and

the traction control is in NEUTRAL.

2. Remove the spark plug wire from the engine spark plug.

g262017

Figure 53

Clutch cable

Cable eyelet

Clutch lever

Jam nut

Retaining ring

3. Remove the clutch cable (item 1 in

Figure 53

) from the transmission

assembly as follows:

A. Loosen the front cable jam nut (2) and lift the clutch cable (1) from the

casting slot of the engine base.

Greensmaster

1018/1021/1026

Page 7–9

Controls, Wheels and Accessories : Service and Repairs

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды