Toro Greensmaster 1018 Скачать руководство пользователя

Страница: 62 / 179

Disassembly of Reel Drive Assembly

g258688

Figure 23

Reel shaft-driven

11.

Socket head screw

21.

Reel shaft-driver

O-ring

12.

Socket head screw (3 each)

22.

Reel drive housing

Pivot sleeve

13.

Expansion plug

23.

O-ring

Reel drive gasket

14.

Reel drive cover

24.

Bolt

Ball bearing (2 each)

15.

Reel pulley - 22 tooth

25.

Lock nut (2 each)

Internal snap ring

16.

Reel belt

26.

Idler arm

Reel pulley spacer (2 each)

17.

Retaining ring

27.

Plain washer

Reel pulley - 24 tooth

18.

Ball bearing (4 each)

28.

Hex bolt

Lock nut (2 each)

19.

Flocked bearing shield

29.

Retaining ring

10.

Idler bushing

20.

Hipro key

Note:

Refer to

Figure 23

during this procedure.

1. Remove the reel drive belt (item 16 in

Figure 23

); refer to

Removing the

Reel Drive Belt (page 5–5)

2. Remove and discard the reel drive gasket (4) from the reel drive housing (22).

3. If necessary, remove the expansion plug (13) from the reel drive cover (14).

4. Remove the hex bolt (28) and plain washer (27) from the idler arm (26) and

the nut (25) from the reel drive housing (22).

5. Loosen and remove the socket head screw (11) that secures the idler arm

(26) to the reel drive housing (22). Remove the idler arm and nut (25) from
the reel driving housing.

6. If necessary, remove the idler bushing (10) from the idler arm (26).

7. Remove the retaining ring (29) and use a press to remove 2 ball bearings

(18) from the idler arm (26). Discard the ball bearings after removal.

8. Remove the lock nut (9), reel pulley (8), hipro key (20) and spacer (7) from

the reel shaft-driven (1).

Traction and Reel Drive Systems: Service and Repairs

Page 5–8

Greensmaster

1018/1021/1026

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды