Toro Greensmaster 1018 Скачать руководство пользователя

Страница: 59 / 179

Service and Repairs

Reel Drive Belt

g258535

Figure 21

Reel drive box assembly

Bolt

Socket head screw (3 each)

Reel belt

Gasket

Idler arm

Reel drive cover

The greensmaster machines use a positive drive belt on the right side of the
machine to operate the cutting unit.

Removing the Reel Drive Belt

Note:

Refer to

Figure 21

during this procedure.

1. Park the machine on a level surface. Ensure that the engine is OFF. Remove

the spark plug wire from the engine spark plug.

2. Remove the 3 socket head screws (7) that secures the reel drive cover (6)

to reel drive assembly (1) and remove the reel drive cover to expose the
reel drive belt (2).

Greensmaster

1018/1021/1026

Page 5–5

Traction and Reel Drive Systems: Service and Repairs

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды