Toro Greensmaster 1018 Скачать руководство пользователя

Страница: 150 / 179

Cutting Unit Assembly

g261511

Figure 77

Cutting unit assembly

Dowel pin (4 each)

Reel drive assembly

Frame assembly

Socket head screw (4 each)

Removing the Cutting Unit Assembly

Note:

Refer to

Figure 77

during this procedure.

1. Park the machine on a level surface on the traction drum. Ensure that the

engine is OFF and the traction control is in NEUTRAL.

2. Remove the spark plug wire from the engine spark plug.

3. Slide the telescopic coupler on the reel drive assembly (2) from the

transmission drive shaft.

Note:

If necessary, remove the reel drive assembly (2) from the cutting unit

assembly (1); refer to

Removing the Reel Drive Assembly (page 5–7)

4. Remove the 4 socket head screws (3) that secures the cutting unit assembly

(1) to the frame assembly (5).

Note:

Support the traction unit and lock the kick stand.

5. Slide and remove the cutting unit assembly (1) from the frame assembly (5).

6. If necessary, remove the dowel pins (4) from the frame assembly (5).

DPA Cutting Units: Service and Repairs

Page 8–16

Greensmaster

1018/1021/1026

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды