Toro Greensmaster 1018 Скачать руководство пользователя

Страница: 61 / 179

Reel Drive Assembly

g258675

Figure 22

Screw (2 each)

V-ring seal

RH side plate

Spacer (2 each)

Reel drive assembly

10.

Transmission drive shaft

Washer (2 each)

Compression spring

11.

Spacer

Spring washer (2 each)

Telescopic coupler

12.

Nut

Removing the Reel Drive Assembly

Note:

Refer to

Figure 22

during this procedure.

1. Park the machine on a level surface. Ensure that the engine is OFF. Remove

the spark plug wire from the engine spark plug.

2. Slide the telescopic coupler (item 8 in

Figure 22

) on the reel drive assembly

(6) and disconnect the reel drive shaft from the transmission drive shaft (10).

3. Loosen and remove the 2 screws (1) and the nut (12) that secures the reel

drive assembly (6) to RH side plate (9). Remove the reel drive assembly
(6), flat washers (3), spring washers (4) and spacers (2 and 11) from the
RH side plate (9).

4. Remove the V-ring seal (5) from the reel drive assembly (6).

Greensmaster

1018/1021/1026

Page 5–7

Traction and Reel Drive Systems: Service and Repairs

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды