Toro Greensmaster 1018 Скачать руководство пользователя

Страница: 81 / 179

Disassembling the Transmission Gear Box Assembly (continued)

3. Remove the oil seal (6), retaining ring (5) from the transmission cover (23).

Use a press to remove the ball bearing (25) from the transmission cover (23).
Discard the oil seals and ball bearing.

g259590

Figure 34

External retaining ring

10.

O-ring (2 each)

19.

Brake lever

Fitting plug

11.

Retaining ring (2 each)

20.

O-ring

Wave washer

12.

Flange bearing (2 each)

21.

Brake clevis pin

Ball bearing (2 each)

13.

Ball bearing (2 each)

22.

Flat wire spring

Neutral spur gear

14.

Differential assembly

23.

Transmission housing assembly

Neutral slider shaft

15.

V-ring seal

24.

Cable brake lever

Square key (2 each)

16.

Retainer plate

25.

Bolt

Bolt (4 each)

17.

Retaining ring

26.

Brake gasket plate

Differential shaft (2 each)

18.

Brake band

4. Remove the neutral spur gear assembly (item 5 in

Figure 34

) and wave

washer (3) from the transmission housing assembly (23).

5. Use a press to remove the ball bearings (4) from the neutral slider shaft

(6). Remove the square keys (7) from the neutral slider shaft (6). Discard
the ball bearings.

6. Remove the differential assembly (14) from the transmission housing

assembly (23).

7. Remove the 2 differential shafts (9) from the differential housing (14).

Remove the retaining rings (11) and O-rings (10) from the differential shafts
(9). Discard the O-rings.

Greensmaster

1018/1021/1026

Page 5–27

Traction and Reel Drive Systems: Service and Repairs

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды