manualshive.com logo in svg

Toro Greensmaster 1018, Руководство по обслуживанию

Поделиться
Скачать
Toro Greensmaster 1018 Скачать руководство пользователя страница 112

Installing the Brake Cable

1. Secure the brake cable (9) to the brake lever assembly as follows:

A. Install the cable spring (7) to the spring anchor on the brake lever

assembly (3).

B. Slide the brake cable into the shift mount bracket slot. Ensure that the jam

nut (8), flat washer and lock washer are both sides of the bracket. Adjust
the jam nuts so that equal amount of cable threads are visible above and
below jam nuts. Leave jam nuts snug until final cable adjustment.

2. Route the brake cable (9) to the transmission gear box assembly and install

the brake cable to the transmission gear box assembly as follows:

A. Install the brake cable eyelet (2) onto the brake lever (3) on transmission

gear box assembly and secure with a snap ring (1).

B. Position the brake cable (5) to the casting slot of the transmission gear

box assembly with a jam nut (4), flat washer and lock washer on each
side of the slot. Adjust and tighten the jam nuts so that equal amount of
cable threads are visible above and below jam nuts.

3. Make final adjustment of the brake cable at the brake cable lever assembly.

Adjust the cable jam nuts to remove the slack in the brake cable.

4. Check the brake cable adjustment; refer to

Operator’s Manual

.

5. Install the lower cover and control cover to the handle assembly.

6. Attach the spark plug wire to the engine spark plug.

Controls, Wheels and Accessories : Service and Repairs

Page 7–8

Greensmaster

®

1018/1021/1026

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды