Toro Greensmaster 1018 Скачать руководство пользователя

Страница: 49 / 179

Installing the Engine

1. If removed, install the muffler (2) onto the engine (14) and secure with the 2

bolts (1).

2. Torque tighten the bolts (1) from

4 to 5.6 N∙m (35 to 50 in-lb)

3. Position the engine (14) onto the engine base (5) and engine output shaft in

the bell housing and external clutch hub.

4. Secure the engine (14) onto the bell housing with the 4 bolts (8) and 4

washers (9). In an alternating cross pattern, torque tighten the bolts (8) from

10 to 11.3 N∙m (90 to 100 in-lb)

5. Secure the engine (14) to the engine base (5) with the 4 carriage bolts (6), 4

washers (4) and 4 nuts (3).

6. Apply the anti-seize lubricant to the engine shaft key.

7. Install the clutch hub clamp (10) onto the external clutch hub and make sure

that the clutch hub clamp integral key is aligned to the engine shaft keyway.
Secure the clutch hub clamp (10) with the 2 bolts (15) and 2 nuts (11).

8. Torque tighten the bolts (15) from

10 to 12.4 N∙m (90 to 110 in-lb)

9. Install the clutch cover (12) onto the bell housing and secure with the 2 bolts

(13). Torque tighten the bolts (13) from

6.7 to 9 N∙m (60 to 80 in-lb)

10. Connect the electrical connections to the engine:

A. Apply dielectric gel to wire harness connectors.

B. Connect the wire harness connectors to the engine armature wire (item

1 in

Figure 15

C. Connect the wire harness ground wire (3) to the engine by installing the

LH rear cap screw, flat washer and a flange nut.

D. Apply a coat of dielectric grease to the wire harness ground terminal

to prevent corrosion.

E. If the machine is equipped with optional lighting kit, connect the wire

harness connectors to the engine alternator wires.

11. Connect the throttle cable (item 2 in

Figure 14

) to the engine:

A. Slide the throttle cable end into the governor lever (1).

B. Place throttle cable (2) under the cable clamp (3) and secure with a screw.

C. Adjust the throttle cable; refer to

Throttle Cable Adjustment (page 4–4)

Ensure that all fasteners are tightened after the cable adjustment.

12. Check and adjust the engine oil level as needed; refer to

Operator’s Manual

13. Attach the spark plug wire to the spark plug. Open the fuel shut-off valve

on the fuel tank.

14. Start the engine and allow it to warm to operating temperature. Check high

and low idle speeds and adjust if necessary.

Greensmaster

1018/1021/1026

Page 4–11

Gasoline Engine: Service and Repairs

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды