Toro Greensmaster 1018 Скачать руководство пользователя страница 43

Страница: 43 / 179

Service and Repairs

Cooling System

g258391

Figure 10

Engine cylinder shroud

Cooling fins

IMPORTANT

The engine that powers the machine is air-cooled. Operating the
engine with dirty or plugged cooling fins or a plugged or dirty blower
housing will result in engine overheating and damage.

1. Park the machine on a level surface. Ensure that the engine is OFF position.

Remove the spark plug wire from the spark plug.

IMPORTANT

Never clean the engine with pressurized water. Water could enter
and contaminate the fuel system.

2. Clean the cooling fins on the cylinder and cylinder head. Remove the engine

cylinder shroud from the engine for more thorough cleaning; refer to

Figure

Greensmaster

1018/1021/1026

Page 4–5

Gasoline Engine: Service and Repairs

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды