Toro Greensmaster 1018 Скачать руководство пользователя страница 120

Страница: 120 / 179

Brake Latch Shaft

g260416

Figure 57

Shoulder bolt

Flange bushing (2 each)

Flange nut

Lever

Brake latch shaft

Brake lock lever

10.

Torsion spring

Roll pin

11.

Flange nut

Bolt

12.

Upper receiver weldment

Disassembling the Brake Latch Shaft

Note:

Refer to

Figure 57

during this procedure.

1. Park the machine on a level surface. Ensure that the engine is OFF and

the traction control is in NEUTRAL.

2. Remove the spark plug wire from the engine spark plug.

3. Remove the bolts and washers that secures the controls covers to the upper

receiver weldment.

4. Using the drift pin, remove the roll pin (5) from the brake lock lever (4).

5. Slide and remove the brake lock lever (4) from the brake latch shaft (9).

Controls, Wheels and Accessories : Service and Repairs

Page 7–16

Greensmaster

1018/1021/1026

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды