Toro Greensmaster 1018 Скачать руководство пользователя

Страница: 143 / 179

Installing the Bedbar (continued)

7. Install the bedbar bolt assemblies (8). Make sure that the washers are not

caught on the threads of the pivot bolts. Torque tighten each bedbar bolt (8)
from

22 to 27 N∙m (190 to 240 in-lb)

IMPORTANT

Do not over tighten the lock nuts as this can distort the side plates
and affect reel bearing alignment. When the lock nut is correctly
tightened, the inside washers may be loose.

8. Tighten both lock nuts (9) until outside metal washers do not have any end

play and can still can be rotated.

9. Tighten the nut (19) on each bedbar adjuster assembly (16) until the adjuster

spring (18) is fully compressed, then loosen the nut (19) to 1/2 turn.

10. Adjust the bedknife to reel contact; refer to the

Cutting Unit Operator’s

Manual

11. Attach the spark plug wire to the engine spark plug.

Greensmaster

1018/1021/1026

Page 8–9

DPA Cutting Units: Service and Repairs

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды