Toro Greensmaster 1018 Скачать руководство пользователя страница 57

Страница: 57 / 179

Adjustments

g258535

Figure 20

Reel drive box assembly

Bolt

Socket head screw (3 each)

Reel belt

Gasket

Idler arm

Reel drive cover

Adjusting the Reel Drive Belt

1. Park the machine on a level surface. Ensure that the engine is OFF. Remove

the spark plug wire from the engine spark plug.

2. Remove the 3 socket head screws (7) that secures the reel drive cover (6)

to the reel drive assembly (1) and remove the reel drive cover to expose
the reel drive belt (2).

3. Check tension by depressing the belt (item 2 in

Figure 20

) at mid span

between pulleys with

18 to 22 N (4 to 5 lbs)

of force. The belt should deflect

6.35 mm (0.25 inch)

. If deflection is incorrect, proceed to next step. If

deflection is correct, continue operation.

Greensmaster

1018/1021/1026

Page 5–3

Traction and Reel Drive Systems: Adjustments

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды