Toro Greensmaster 1018 Скачать руководство пользователя страница 65

Страница: 65 / 179

Drum Drive Gear Box Assembly

g258813

Figure 25

Transmission gear box assembly

Lock nut

Frame assembly

Traction drum

Shoulder bolt (3 each)

10.

Shoulder bolt

Splined coupler (2 each)

RH hex shaft

11.

Truss screw

Washer

Drum drive gear box assembly

Removing the Drum Drive Gear Box Assembly

Note:

Refer to

Figure 25

during this procedure.

1. Park the machine on a level surface. Ensure that the engine is OFF. Remove

the spark plug wire from the engine spark plug.

2. Remove the transport wheel if attached; refer to

Removing the Transport

Wheel (page 7–27)

Note:

Support the machine on kickstand during this operation.

3. Move the traction engage/disengage lever to the disengage position to

remove torque from the drum drive gears.

Greensmaster

1018/1021/1026

Page 5–11

Traction and Reel Drive Systems: Service and Repairs

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды