Toro Greensmaster 1018 Скачать руководство пользователя страница 133

Страница: 133 / 179

Assembling the Transport Wheel

1. If the shoulder screws were removed from the hub, apply Loctite #242 (or

equivalent) to the threads of the shoulder screws. Secure the torsion spring
and retaining lever to the hub with the shoulder screws.

2. Assemble the tire, tube, and deep rim.

3. Install the shallow rim into the tire. Align and secure the shallow rim tot he

deep rim with 4 bolts and 4 flange nuts. Tighten the fasteners.

4. Install the hub into the deep rim. Secure the hub to the deep rim with the 3

bolts and 3 lock washers. Tighten the fasteners.

5. Inflate the tire to

83 to 103 kPa (12 to 15 psi)

Installing the Transport Wheel

1. Ensure that the machine is parked on a level surface.

2. Support the machine onto the kickstand.

3. Slide the transport wheel completely onto the wheel hex shaft until the wheel

retaining lever is secured into the groove onto the wheel hex shaft.

Greensmaster

1018/1021/1026

Page 7–29

Controls, Wheels and Accessories : Service and Repairs

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды