Toro Greensmaster 1018 Скачать руководство пользователя страница 72

Страница: 72 / 179

Disassembly of Drum Drive Assembly

g258879

Figure 29

Traction drum (2 each)

Drum spindle

Spacer

Bolt (8 each)

Seal (2 each)

10.

Drum hub

Lock washer (8 each)

Ball bearing (2 each)

11.

Shoulder bolt (6 each)

Drum hub plate (2 each)

Spacer

12.

Lock nut

Note:

Refer to

Figure 29

during this procedure.

1. Remove the 4 bolts (item 2 in

Figure 29

) and lock washers (3) that secures

the drum hub plate (4) to the drum spindle (5).

2. Remove the 4 bolts (2) and lock washers (3) that secures the drum hub

plate (4) to the drum hub (10).

3. Remove the shoulder bolts (11) that secures the drum hub plate (4) to the

traction drum (1).

4. Remove the lock nut (12) that secures the drum spindle (5) and drum hub

(10) together. Carefully slide and remove the drum spindle (5) out of the
drum hub (10).

5. Remove the 2 seals (6) from the drum hub (10). Use a press to remove the 2

ball bearings (7) and a bearing spacer (8) from the drum hub (10). Discard
the ball bearings.

Traction and Reel Drive Systems: Service and Repairs

Page 5–18

Greensmaster

1018/1021/1026

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды