Thermo Orion Star Скачать руководство пользователя | Manualshive

Страница: 64 / 111

background image

Thermo Electron Corporation

IX-8

Orion Star Series Meter

The will flash until the reading is stable . Once the reading is stable you
can Log & Print the measurement by pressing the

. If you are recording

the data into a notebook, record the pH as well as the temperature at which
the pH reading is taken . If the stirrer is in motion, press

to turn off the

stirrer before removing the stirrer from the sample .

b . If you are in AUTO-READ™ mode then press

to start the measurement .

Once the reading is stable the meter will automatically Log & Print the
results and freeze the display . If the stirrer is enabled, then the stirrer will
turn on when

is pressed and turn “off” once the reading has stabilized .

When using the AutoStir™ BOD Probe, pressing the button on the probe will
start the AUTO-READ measurement .

c . If you are in Timed Measurement mode then the meter will start making

measurements as soon as it goes into measurement mode at the frequency
selected in setup . It will automatically Log & Print each measurement . If
you are using the benchtop meter and the stirrer control is enabled then
pressing

will start the stirrer . Pressing

again will turn off the stirrer .

3 . Remove the electrode from the sample and rinse with deionized water, then

place it in your next sample and repeat step 2 .

4 . When all samples have been measured, rinse the electrode with deionized

water and blot dry . Consult your electrode manual for proper electrode storage
instructions .

«
...
62
63
64
65
66
...
»

Содержание Orion Star
















































































































Отзывы:

Нет отзывов

Похожие инструкции для Orion Star

Бренд: Kawai Страницы: 33

Бренд: Kawai Страницы: 60

Charge Analyzer 711

Бренд: 3M Страницы: 24

Бренд: Lumel Страницы: 32

Бренд: Raymarine Страницы: 42

Бренд: janitza Страницы: 128

Бренд: Clavitech Страницы: 56

Бренд: NIEUWKOOP Страницы: 2

Бренд: Dadam micro Страницы: 24

Бренд: promesstec Страницы: 72

Бренд: Universal Laser Systems Страницы: 100

LaserRange-Master i5

Бренд: LaserLine Страницы: 68

Бренд: Seli Страницы: 68

Бренд: Joinwit Страницы: 24

Бренд: Fluke Страницы: 14

Бренд: Boston Musical Products Страницы: 3

Microsensor Multimeter

Бренд: UNISENSE Страницы: 8

Бренд: Hanna Instruments Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды