manualshive.com logo in svg

Teledyne 300, Инструкция по эксплуатации, Страница: 96 / 111

Поделиться
Скачать
Teledyne 300 Скачать руководство пользователя страница 96

 

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 90

 

 

10.6.7  Checking the Opto Interrupter 

Correct operation of the Opto Interrupter on the gas filter wheel can be confirmed by 
connecting an oscilloscope U6, Pin 11 on the Sync Demodulator board and comparing 
the waveform to Figure 10.1.  The waveform should be symmetrical and 5 Volts peak to 
peak. 
 
 
 
 

 

FIGURE 10.1 OPTO PICKUP 

WAVEFORM  

FIGURE 10.2 DETECTOR 

WAVEFORM 

 

10.6.8  Checking Optical Alignment 

The mirrors used in the optical system of the Model 300 are designed to have their 
alignment set permanently during the manufacturing process and no adjustment is 
normally needed.  If the optical system is disassembled or if failure of any of the optical 
components is suspected, the instrument can be checked for proper optical alignment as 
follows: 

1. 

Connect a source of zero air to the analyzer. 

2. 

Allow the analyzer to warm-up for 60 minutes. 

3. 

Confirm Optical System Energy through-put by: 
a) 

Press the TST> or TST< button on the front panel until the CO    
 MEAS value is displayed. 

b) 

Increase the gain of the Synchronous Demodulation by turning      Pot 
R7 on the Sync Demodulator board clockwise.  If a CO      MEAS 
value of 5000 mV can obtained, energy throughput is     acceptable. 

c) 

 Re-adjust Pot R7 on the Sync Demodulator Board to obtain a CO    
 MEAS reading of 4200 mV (

±

200). 

4. 

 Connect an oscilloscope to U7-Pin 1.  Sync the oscilloscope on this 
channel. 

Содержание 300
















































































































Отзывы:

Нет отзывов