manualshive.com logo in svg

Teledyne 300, Инструкция по эксплуатации, Страница: 57 / 111

Поделиться
Скачать
Teledyne 300 Скачать руководство пользователя страница 57

 

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 51

 

 

 

The 

TEST

 button is used to scroll through the test measurements until the one of interest 

is displayed.  To turn the test on press the 

OFF/ON

 button.  Viewing test measurements 

in the diagnostic mode is especially useful for viewing the results of a diagnostic test. 
 
The 

PREV

 button goes to the previous diagnostic test.  When pressed, the CPU turns the 

current diagnostic test OFF if it is ON. The 

NEXT

 button goes to the next diagnostic test.  

When pressed, the CPU turns the current diagnostic test OFF if it is ON. The 

EXIT

 

button exits the diagnostic mode and turns all the diagnostic tests OFF.  This ensures that 
a diagnostic test is not accidentally left ON.  A message is also sent to the RS-232 
channel to indicate that the diagnostic mode has been exited. 

DIAGNOSTIC TESTS 

Test # 

 Name 

 Signal  

 Nominal Value 

1 NONE 

No 

output 

0 

mV 

2 

CO MEASURE 

CO detector measure value 

4500 mV 

3 

CO REFERENCE 

CO detector reference 

value 

4200 mV 

4 

SAMP PRESS 

Sample pressure 

125 mV 

5 

SAMP FLOW 

Sample flow 

3000 mV 

6 

SAMP TEMP 

Sample temperature 

3000 mV 

7 

BENCH TEMP 

Optical bench temperature 

3900 mV 

8 

WHEEL TEMP 

Outputs filter wheel temp. 

3900 mV 

9 

CHASSIS TEMP 

Outputs Chassis temp 

2740 mV 

10 

DCPS VOLT   

Outputs DC power 

2500 mV 

11 

DAS AVERAGE 

Current DAS average 

Any 

TABLE 5.1  

 

5.2.1  Signal I/O 

The signal I/O diagnostic mode gives the user access to the digital and analog inputs and 
outputs on the V/F board.  The digital outputs can be controlled through the keyboard. 
Any signals manually changed through the signal I/O menu will remain in effect until 
you leave the signal I/O menu.  At that time the analyzer will regain control of these 
signals. To enter the signal I/O test mode, press 

SETUP-MORE-DIAG-ENTR

.  When 

the diagnostic mode is entered, a message is sent to the RS-232 channel indicating entry 
into the diagnostic mode. Use the 

PREV

 and 

NEXT

 buttons to scroll through the signals.  

Edit buttons will appear for the signals that can be controlled by the user.  Press 

JUMP

 to 

skip to a specific I/O Signal. 
 
Table 5.2 below lists the I/O signals available for the M300: 
 

Содержание 300
















































































































Отзывы:

Нет отзывов