manualshive.com logo in svg

Teledyne 300, Инструкция по эксплуатации, Страница: 36 / 111

Поделиться
Скачать
Teledyne 300 Скачать руководство пользователя страница 36

 

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 30

 

 

3.1.3  Dual Range Calibration 

If the analyzer is being operated in Dual Range mode or Auto-Ranging mode, then the 
High and Low ranges must be independently calibrated.  When the analyzer is in Dual or 
Auto Range mode you will be prompted to enter the range to calibrate whenever you 
enter a calibration command from the front panel.  Press 

HIGH

 or 

LOW

 followed by the  

ENTR 

button to proceed with the calibration.  To calibrate the other range you must exit 

to the sample menu and restart the calibration.  See Section 4.6 for more information on 
the Range Modes.  The following procedure shows an example of how to calibrate the 
two ranges with calibration gas coming in through the sample port: 
 

Step 

Action 

Comment 

1. Press 

CAL

 

Analyzer enters M-P calibration mode.  Calibration gas 
source should be set to deliver zero gas to the sample port. 

2. Press 

LOW-ENTR

 

Select range to calibrate 

3. 

Wait 15 min. 

Wait for CO reading to stabilize at zero value. 

4. Press 

ZERO-ENTR

 Changes 

calibration 

equations for Low range so analyzer 

will read zero. 

5. Press 

CONC

 

Enter span gas concentration for Low range.  

6. 

Key in span 
concentration 

Enter span gas concentration for Low Range. Set 
calibration gas source to deliver span concentration 

7. Press 

ENTR

 

 

8. 

Wait 15 min. 

Wait for CO reading to stabilize at span value 

9. Press 

SPAN-ENTR

 Changes 

calibration 

equations for Low range so analyzer 

will read span value. 

10. Press 

EXIT

 

Exits back to sample menu 

Repeat steps 1-10 for High range. 

 

3.2  IZS zero/span check (Option) 

If the IZS (Internal Zero Scrubber) option has been installed and a source of CO span gas 
has been connected, the operator can check the zero and span setpoints of the analyzer at 
any time by pressing the 

CALZ

 or 

CALS

 button. 

 
Pressing 

CALZ

 switches the Sample/Cal valve and allows the analyzer to draw air 

through the zero air scrubber.  After a few minutes the CO reading should go to zero.  If 
it doesn't, the operator may press the 

ZERO

 button followed by 

ENTR

. 

 

CALS

 works like 

CALZ

 except that externally supplied span gas is drawn through the 

analyzer.  After a few minutes the CO reading should approach the span level (typically 
40 PPM).  If it doesn't, the operator may press the 

SPAN

 button, followed by 

ENTR

.  

The expected span gas concentration may be changed by pressing the 

CONC

 button. 

 
The operator can exit the IZS calibration only by pressing the 

EXIT

 button.  If either the 

ZERO

 or 

SPAN

 buttons were pressed and 

ENTR

 was not pressed, the Analyzer will 

beep once to indicate that no changes have been made. 

Содержание 300
















































































































Отзывы:

Нет отзывов