Teledyne 300 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 111

Teledyne 300 Скачать руководство пользователя страница 46

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 40

NEXT

until D/A CALIBRATION is displayed and press

ENTR.

Press

CFG

to enter the

D/A configuration menu. Use the

NEXT

and

PREV

buttons to select the desired analog

output and press

SET

. Enter a value of from -500 mV to +500 mV (other ranges will

ratio accordingly), followed by

ENTR

to accept the change, or

EXIT

to leave it

unchanged. The offset will be reflected immediately on the strip chart recorder or other
instrument.

4.8 Setting the RS-232 baud rate

To set the baud rate for the RS-232 channel, press

SETUP-MORE-COMM-BAUD

.

Press

300

,

1200

,

2400

,

4800

,

9600

, or

19.2

followed by

ENTR

to accept the new baud

rate, or

EXIT

to leave the baud rate unchanged.

4.9 Setting the analyzer I.D.

Each Analyzer may be programmed with a unique I.D. number which appears on all RS-
232 messages. To set the Analyzer I.D., press

SETUP-MORE-COMM-ID

. Enter a 4-

digit number from 0000 to 9999, followed by

ENTR

to accept the new I.D., or

EXIT

to

leave the I.D. unchanged. If changed, the new I.D. number will appear on all RS-232
reports from this Analyzer.

4.10 Disabling the calibration password

Normally, operators are required to enter the calibration password when doing a manual
calibration via the

CALZ

,

CALS

, or

CAL

buttons. To allow calibration without entering

the password, press

SETUP-PASS

and set it to OFF, and then press

ENTR

to accept the

change, or

EXIT

to leave it unchanged. To enable the calibration password, set the

variable to ON.

4.11 Data acquisition system (DAS)

The Model 300 contains a flexible and powerful built in data acquisition system (DAS)
that enables the analyzer to store concentration data as well as many diagnostic
parameters in its battery backed memory. This information can be viewed from the front
panel or printed out through the RS-232 port. The diagnostic data can be used for
performing “Predictive Diagnostics” and trending to determine when maintenance and
servicing will be required.

The logged parameters are stored in what are called “Data Channels.” Each Data
Channel can store multiple data parameters. The Data Channels can be programmed and
customized from the front panel. A set of default Data Channels has been included in the
Model 300 software. These are described Section 4.11.1. For more information on
programming custom Data Channels, a supplementary document containing this
information can be requested from Teledyne API.

«
...
44
45
46
47
48
...
»

Содержание 300
















































































































Отзывы:

Нет отзывов