Teledyne 300 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 111

Teledyne 300 Скачать руководство пользователя страница 67

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 61

DIAGNOSTIC COMMANDS

Command

Function

D ENTER SIG

Enter diagnostic Signal I/O mode

D EXIT

Exit diagnostics mode

D LIST

Prints all Signal I/O values. See Table

5.2 for Signal Definitions

D name[=value]

Examines or sets I/O signal. See

Table 5.2 for a list of signals. Must

issue D ENTER SIG before using this

command.

D RESET

Reset analyzer(same as power on)

D RESET RAM

Resets analyzer and erases RAM.

Erases all DAS data. Keeps setup

variables and calibration

D RESET EEPROM

Resets analyzer and erases RAM and

EEPROM. Erases all DAS data.

Resets all setup variables to factory

default. Resets calibration values.

TABLE 7.5

These commands may be used whether the diagnostics have been entered from the
keyboard (SETUP-DIAG) or the RS-232 ("D ENTER <CRLF>"). However, when the
diagnostics are entered via the keyboard, no feedback is sent to the RS-232 channel. This
prevents the RS-232 output from getting unnecessarily cluttered with diagnostic data.

Whenever the diagnostic mode is entered or exited, a report is issued to the RS-232
output. The table below summarizes the diagnostic reports.

DIAGNOSTIC REPORTS

Report

"C DDD:HH:MM IIII ENTER DIAGNOSTIC MODE"

"C DDD:HH:MM IIII EXIT DIAGNOSTIC MODE"

TABLE 7.6

NOTE

THE DIAGNOSTICS MODE MAY ONLY BE

ENTERED VIA THE RS-232 PORT WHEN

THE ANALYZER IS IN SAMPLE MODE.

«
...
65
66
67
68
69
...
»

Содержание 300
















































































































Отзывы:

Нет отзывов