Teledyne 300 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 111

Teledyne 300 Скачать руководство пользователя страница 8

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 2

1.2 Warranty

WARRANTY POLICY

Prior to shipment, Teledyne API equipment is thoroughly inspected and tested. Should
equipment failure occur, Teledyne API assures its customers that prompt service and
support is available.

COVERAGE

After the warranty period and throughout the equipment lifetime, Teledyne API stands
ready to provide on-site or in-plant service at reasonable rates similar to those of other
manufacturers in the industry. All maintenance and the first level of field troubleshooting
is to be performed by the customer.

NON-TELEDYNE API MANUFACTURED EQUIPMENT

Equipment provided but not manufactured by Teledyne API is warranted and will be
repaired to the extent and according to the current terms and conditions of the respective
equipment manufacturer’s warranty.

GENERAL

Teledyne API warrants each Product manufactured by Teledyne API to be free from
defects in material and workmanship under normal use and service for a period of one
year from the date of delivery.
If a Product fails to perform to its specifications, Teledyne API shall correct such defect
by, in Teledyne API's discretion, repairing or replacing such defective Product or
refunding the purchase price of such Product.
The warranties set forth in this section shall be of no force or effect with respect to any
Product: (i) that has been altered or subjected to misuse, negligence or accident, or (ii)
that has been used in any manner other than in accordance with the instruction provided
by Teledyne API or (iii) not properly maintained.

THE WARRANTIES SET FORTH IN THIS SECTION AND THE REMEDIES
THEREFORE ARE EXCLUSIVE AND IN LIEU OF ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE OR OTHER
WARRANTY OF QUALITY, WHETHER EXPRESSED OR IMPLIED. THE
REMEDIES SET FORTH IN THIS SECTION ARE THE EXCLUSIVE REMEDIES FOR
BREACH OF ANY WARRANTY CONTAINED HEREIN. TELEDYNE API SHALL
NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF OR RELATED TO THIS AGREEMENT OF TELEDYNE API’s
PERFORMANCE HEREUNDER, WHETHER FOR BREACH OF WARRANTY OR
OTHERWISE.

TERMS AND CONDITIONS

All units or components returned to Teledyne API should be properly packed for
handling and returned freight prepaid to the nearest designated Service Center. After the
repair, the equipment will be returned, freight prepaid.

«
...
6
7
8
9
10
...
»

Содержание 300
















































































































Отзывы:

Нет отзывов