Teledyne 300 Скачать руководство пользователя страница 80

Страница: 80 / 111

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 74

To view the current dark offset, press

SETUP-MORE-DARK-VIEW.

Press

EXIT

when finished. No password is required to view the dark offset, only to change it.

9.4 Output voltage range changes

Output voltage ranges are set by DIP Switch settings on the V/F board. To change the
range for the analog outputs:

Turn off instrument power. Remove the instrument cover. Locate the V/F
board near the top of the drawing using Figure 1.6.

Locate switches S1, S2, and S3 along the top edge of the card. Select the
desired range by setting the switches as shown in Table 9.1, below.

V/F BOARD SWITCH SETTINGS - RANGES FOR ANALOG OUTPUT

Switch

100 mV

Full Scale

1 V

Full Scale

5 V

Full Scale

10 V

Full Scale

S1 (Recorder Output)

1, 6

1, 5

1, 4

1, 3

S2 (DAS Output)

1, 6

1, 5

1, 4

1, 3

S3 (Test Output)

1, 6, 7

1, 5, 7

1, 4, 7

1, 3, 7

TABLE 9.1

NOTE

TO ADJUST ANALOG RECORDER OFFSET,

SEE SECTION 4.7.

Содержание 300
















































































































Результаты поиска

Содержание 300

Отзывы:

Teledyne 300, Инструкция по эксплуатации, Страница: 80 / 111

Результаты поиска

Содержание 300

Отзывы: