manualshive.com logo in svg

Teledyne 300, Инструкция по эксплуатации, Страница: 100 / 111

Поделиться
Скачать
Teledyne 300 Скачать руководство пользователя страница 100

 

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 94

 

 

b. 

Open the front panel and remove the transparent filter cover and knurled 
retaining ring. 

c. 

Remove the teflon hold-down O-ring. 

d. 

Remove the old filter element and discard. 

e. 

Install a new filter element in the filter cavity.  Be careful with the 
element, it is fragile.   

f. 

Replace the hold-down O-ring on top of the filter element. 

g. 

Replace the filter top and re-tighten. 

h. Leak 

check. 

i. 

Turn on the Analyzer. 

11.3  Leak checking 

There are two methods of leak checking: 

11.3.1 Using a leak checker 

 Turn the power off.  Disconnect the fittings from the pump and bypass the pump.  
Connect the leak checker to the sample inlet of  the Model 300.  Cap the exhaust of the 
analyzer.  Set the leak checker to pressure mode. 

Leave the checker on until 15 psi is achieved. Close the valve and ensure the pressure 
remains at 15 psi for at least 5 minutes.  If pressure drops more than 1 psi, there is a leak 
and it must be repaired. 
  
 If there is a  leak  present, pressurize the Model 300  to 15 psi and put soap bubble 
solution on pneumatic assemblies until the leak is found. 
 

CAUTION 

 

DO  NOT  EXCEED  15  PSI  OF  PRESSURE. 

Содержание 300
















































































































Отзывы:

Нет отзывов