manualshive.com logo in svg

Teledyne 300, Инструкция по эксплуатации, Страница: 35 / 111

Поделиться
Скачать
Teledyne 300 Скачать руководство пользователя страница 35

 

P/N 02163G Teledyne API Model 300 CO Analyzer Instruction Manual - Page 29

 

 

3.0  PERFORMANCE TESTING 

Zero/span checking and calibration of the Teledyne API CO Analyzer is divided into two 
sections. Chapter 3 discusses the different methods by which the Analyzer's zero and 
span settings may be checked and adjusted.  The emphasis in Chapter 3 is on the 
operation of the buttons and the internal adjustments they make in the instrument. 

3.1  Manual zero/span check  

 
Operators can manually check the zero and span setpoints of the Analyzer while in 
sample mode by allowing the instrument to sample calibration gas and pressing the 

CAL

 

button.  This is also referred to as a multi-point calibration. 

3.1.1  Zero Check 

Allow the analyzer to sample zero air through the sample port.  Press 

CAL

 button. After 

a few minutes the CO reading should go to zero.  If it doesn't, the operator may press the 

ZERO

 button followed by 

ENTR

.  This will force the CO reading to go to zero and 

modify the internal formulas used to compute the CO reading.  If the 

ZERO

 button is not 

displayed, this means that the zero reading is too far out of adjustment to do a reliable 
calibration.  The reason for this must be determined before the analyzer can be calibrated.  
See Section 10.5 for troubleshooting calibration problems.  Pressing 

EXIT

 will bring you 

back to the Sample menu or you can leave the instrument in CAL mode if you are also 
going to make a span check. 

3.1.2  Span Check 

Allow the analyzer to sample span gas through the sample port.  Press 

CAL

 button. After 

a few minutes the CO reading should be at the expected concentration. If the correct 
concentration is not reached, then the instrument can be adjusted to read the correct 
value. To do this, press 

CONC

 and enter the expected concentration for calibration. The 

SPAN

 button should now be displayed on the front panel.  Pressing 

SPAN

 and 

ENTER

 

will modify the internals formulas used to compute the CO reading.   If the 

SPAN

 button 

is not displayed, this means that the span reading is too far out of adjustment to do a 
reliable calibration.  The reason for this must be determined before the analyzer can be 
calibrated.  See Section 10.5 for troubleshooting calibration problems. 

NOTE

 

 

ZERO OR SPAN CHECKS CAN BE PERFORMED IN ANY 

ORDER. 

Содержание 300
















































































































Отзывы:

Нет отзывов