Sony PetaSite DMS-B110S Скачать руководство пользователя страница 91

Страница: 91 / 112

6-65

DMS-B150L/B210S/B80L/B110S/EX150L/EX210S

For the DMSA-CBJEX

1. When one to three units of the DMS-B150L/

B210S are installed.

(1) Pass the harness (DMS-B150L side) of the already

wired AC outlet (6-pin) through the bottom hole of the
frame to the first DMS-EX150L/EX210S that is
adjacent to the DMS-B150L/B210S, and connect it to
terminal (AC OUT1) of the AC unit (30A) assembly.

(2) Connect the AC IN harness to the terminal (AC IN) of

the AC unit (30A) assembly.

(3) Connect the harness of the already wired AC outlet

through the bottom hole of the frame to the AC outlet
of the first extension console.

(4) Connect the AC power in the same way as step (3) for

the second and third extension consoles.

Harness of the already wired AC outlet

DMS-
B150L/B210S

First extension
console

AC unit (30A) assembly

Screws
(P3

Harness (GRN)

Harness (WHT)

Harness (BLK)

Terminal table screws
(M4

GRN

WHT

BLK

AC outlet (6-pin)

First extension
console

Second extension
console

AC outlet (6-pin)

6-11. Installing the Package Supporting Equipment

AC IN harness

AC Unit (30A) assembly

Screws
(P3

Harness (RED)

Harness (WHT)

Harness (BLK)

Terminal table screws
(M4

Содержание PetaSite DMS-B110S

















































































































Результаты поиска

Содержание PetaSite DMS-B110S

Отзывы:

Похожие инструкции для PetaSite DMS-B110S

Бренды по названию

Популярные бренды

Sony PetaSite DMS-B110S, Руководство по установке

Результаты поиска

Содержание PetaSite DMS-B110S

Отзывы:

Похожие инструкции для PetaSite DMS-B110S

Бренды по названию

Популярные бренды