Sony PetaSite DMS-B110S Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 112

background image

6-47

DMS-B150L/B210S/B80L/B110S/EX150L/EX210S

Removing the Bin Assembly

1.

While referring to “1. Rear door

_

Removal” of

Section “6-3. Removal of the Shipping Metal Fix-
tures”, open the rear door.

2.

Use the screwdriver (long shaft type) to remove the
screws securing the side bin plate around the bin
assembly to be removed.

3.

Draw the side bin plate in the direction of the arrow
and remove the side bin plate while inclining it until it
is removed from the right and left guides.

4.

Remove the four screws and remove the bin assembly.

n

To install the fifth drive in DMS-B210S and the third drive
in DMS-B110S, add the following procedure to remove the
bin assembly after steps 1 through 3.

Side bin plate

Bin
assembly

PWH4

x

8

PWH4

x

8

PWH4

x

8

6-9-2. Extension Console

The GY-2120 or GY-8240/DIR-240 and VTR of 4U (or
5U) can be installed in the extension console.

w

Attach the VTRs or tape drives of the same model to the
top and bottom stages.

Installation Procedures of the Drives

m
.

The unit is set for installing the VTR of 5U when
shipped from the factory. To install the VTR of 4U,
change the setting.

.

Feet must be replaced before installing the GY-2120 and
VTR. Replace the original feet with those supplied with
the extension console.

.

When installing the HDCAM VTR (HDW-500/HDW-
F500), slant the control panel at 15

d

(the front surface

should be slanted at about 30

d

) as shown in the figure

and fix it at the position.
For the procedure of opening and closing the control
panel, refer to the HDCAM VTR Maintenance Manual.
(When the BKDW-515 is attached to the front panel of
the VTR, set the control panel in the same way.)

Replacing the Feet

Remove the two screws, remove the front two feet from the
bottom of the unit, then replace these with the supplied two
feet (VTR feet assembly : X-3068-172-1).

6-9. Installation of the Tape Drive

PWH4

x

8 (a)

PWH4

x

8 (b)

1

Loosen the two PWH4

x

8 (b) screws.

2

Remove the four PWH4

x

8 (a) screws and remove the bin assembly.

3

Fasten the two PWH4

x

8 (b) screws again.

Hexagonal head
cap bolt M4

PS4

x

20

PS4

x

20

Foot before
replacement

Foot after replacement

30

d

15

d

HDCAM VTR

Control panel

«
...
71
72
73
74
75
...
»

Содержание PetaSite DMS-B110S

















































































































Отзывы:

Нет отзывов

Похожие инструкции для PetaSite DMS-B110S

LITTLE BIG DISK THUNDERBOLT 2

Бренд: LaCie Страницы: 6

DataTraveler Locker+ Generation 3 DTLPG3

Бренд: Kingston Technology Страницы: 1623

Бренд: Premio Страницы: 3

Бренд: QNAP Страницы: 321

Бренд: IBM Страницы: 16

Бренд: Gardiun Страницы: 26

Aeon J460 M2 JBOD

Бренд: Netberg Страницы: 67

MaxAttach NAS 4000

Бренд: Maxtor Страницы: 2

StorageTek T10000D

Бренд: Oracle Страницы: 51

Бренд: LaCie Страницы: 26

Бренд: AIC Страницы: 64

Бренд: FRANKLINWH Страницы: 81

Бренд: WiebeTech Страницы: 8

Бренд: HOLZMANN MASCHINEN Страницы: 18

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 3

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды