Sony PetaSite DMS-B110S Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 112

background image

6-51

DMS-B150L/B210S/B80L/B110S/EX150L/EX210S

(3) The holes of the drive stage that are used to fix the

tape drive or the VTR, are different depending upon
the drive whether it is tape drive or VTR. Use position
1 when the tape drive is installed, and use position 2
when the VTR is installed. If the blind plate hinders,
move the blind plate by turning it upside down for the
correct position.

n

The heights of the slide supports are already set to the
specified heights in each position. However, the blind
plates need to be fixed at the correct positions.

Blind plate

Blind plate

Position 1
(when the tape drive is installed)

Position 2
(when the VTR is installed)

PWH3

x

6

PWH3

x

6

: Holes that are used for tape drive installation
: Holes that are used for VTR installation

Slide support

Slide
support

6-9. Installation of the Tape Drive

2. Installing in the bottom stage of the drive

stage

(1) Remove the drive stage panel while referring to

Section 6-5.

(2) Loosen the two fixing screws of the drive stage and

pull out the drive stage until the lock levers of the right
and left rails are locked.

Fixing screw

Lock lever

Lock lever

«
...
75
76
77
78
79
...
»

Содержание PetaSite DMS-B110S

















































































































Отзывы:

Нет отзывов

Похожие инструкции для PetaSite DMS-B110S

Premier 23231GK

Бренд: ABSCO SHEDS Страницы: 25

Бренд: ABSCO SHEDS Страницы: 23

Бренд: ABSCO SHEDS Страницы: 37

Бренд: ABSCO SHEDS Страницы: 40

Бренд: ABSCO SHEDS Страницы: 18

Бренд: ABSCO SHEDS Страницы: 22

Бренд: G-Technology Страницы: 51

Бренд: QNAP Страницы: 321

Бренд: LaCie Страницы: 2

Vertical Modular Paint Storage

Бренд: Blueshark Studio Страницы: 7

Cold Frame Single

Бренд: Palram Страницы: 11

Бренд: LaCie Страницы: 48

Бренд: Overland Storage Страницы: 4

StoreVirtual 3200

Бренд: HPE Страницы: 54

Бренд: HOMEDEPOT Страницы: 24

TERASTATION HS-D1.0TGL/R5

Бренд: Buffalo Страницы: 2

Бренд: Netstor Страницы: 11

StorageTek SL8500

Бренд: Oracle Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды