manualshive.com logo in svg

Sony PetaSite DMS-B110S, Руководство по установке, Страница: 4 / 112

Поделиться
Скачать
Sony PetaSite DMS-B110S Скачать руководство пользователя страница 4

2

DMS-B150L/B210S/B80L/B110S/EX150L/EX210S

5. About Installation Work

5-1.

Notes during Installation ............................................................................. 5-1

5-2.

Tools ............................................................................................................ 5-2

6. Installation Procedure

6-1.

Installation Flow .......................................................................................... 6-1

6-2.

Removal and Installation of the Cabinets ................................................... 6-2

6-3.

Removal of the Shipping Metal Fixtures .................................................... 6-6

6-4.

Installation of the Basic Console ............................................................... 6-10

6-5.

Connecting Extension Consoles ................................................................ 6-12

6-6.

Installation of DMSA-CBL1 ..................................................................... 6-28

6-7.

Prevention of Falling ................................................................................. 6-37

6-8.

Voltage Selector Setting and Notes ........................................................... 6-42

6-9.

Installation of the Tape Drive ................................................................... 6-43

6-9-1.

Basic Console ........................................................................... 6-43

6-9-2.

Extension Console .................................................................... 6-47

6-9-3.

Routing the Cables to Be Connected to the Drives .................. 6-54

6-10. Setting the Switches .................................................................................. 6-55

6-11. Installing the Package Supporting Equipment .......................................... 6-57

6-11-1. Installation of the DMSA-TS08/TS16 ..................................... 6-57
6-11-2. Installation of the DMSA-EH16/EHAC/EHACK ................... 6-60
6-11-3. Installation of the DMSA-CBJ80/CBJ15/CBJEX ................... 6-62
6-11-4. Installation of the DMSA-AT80 .............................................. 6-68
6-11-5. Installation of the DMS-PCU1 ................................................. 6-70
6-11-6. Installation of the DMS-FSW24/28 ......................................... 6-72
6-11-7. Installation of the DMSA-SBE1 .............................................. 6-73

6-12. Wiring Inside Console ............................................................................... 6-74

7. Connecting the Cables

7-1.

Connecting the Power Cable and the UPS .................................................. 7-1

7-1-1.

Connecting the Power Cable ...................................................... 7-1

7-1-2.

Connecting the UPS Cables and Setting the Switches ............... 7-1

7-2.

Signal Input/Output ..................................................................................... 7-2

7-3.

Connecting Connectors and Cable .............................................................. 7-4

8. Operation Check

Содержание PetaSite DMS-B110S

















































































































Отзывы:

Нет отзывов