SOLZAIMA Hidro 12 Скачать руководство пользователя страница 121

Страница: 121 / 147

115

Reading performance curve

For a given speed, the pump can overcome a given pressure drop, for a given flow:

- The pressure drop (or manometric height) is identified on the ordinate axis, with the

units in metres (m) - It depends on the installation.

- The flow rate is identified on the x-axis, with the units in cubic metres per hour (m

/h)

- Depends on the power to be conditioned.

- Constant velocity curves are present in the graph, identified in I, II and III.

- The installer must set the required curve from the lowest to the highest speed by

means of the required flow rate and the head loss of the installation.

- The pumps run at the highest speed in the factory.

Figure 81 - Pump performance - Constant speeds I, II and III

Содержание Hidro 12




















































































































































Результаты поиска

Содержание Hidro 12

Отзывы:

Похожие инструкции для Hidro 12

Бренды по названию

Популярные бренды

SOLZAIMA Hidro 12, Инструкция по эксплуатации

Результаты поиска

Содержание Hidro 12

Отзывы:

Похожие инструкции для Hidro 12

Бренды по названию

Популярные бренды